Telecommunication FTTH SC APC UPC optical fiber fast connectors
Product Description :
Component list:
Back cover opening tool
Optical fiber connector back cover
Optical fiber connector body
Pin protection cap
Optical fiber connector protective jacket
Installation Notes :
For optical cable stripping, use sheathed cable stripping pliers to strip the sheathed cable with a length of about 60mm;
Use Miller pliers to peel off the 0.25mm coating, leaving about 24mm;
Wipe clean with absolute alcohol;
Use a fiber cleaver to cut the fiber, leaving a length of about 48mm;
Fiber positioning and fixing :
1. Screw the edge of the pin protection cap tightly and open the back cover of the optical fiber connector;
2. Use the back cover opening tool to buckle in and push forward according to the direction shown in the figure;
3. Insert the stripped optical cable into the guide hole in the middle;
4. When the outer sheath of the optical cable reaches the fixed teeth, tilt the optical cable by 30-45°;
5. Continue to push the optical cable until the core touches the ferrule protective cap;
6. Press the outer sheath of the optical cable into the tooth-shaped groove, and ensure that the optical fiber has a small amount of slight bending;
7. Close the back cover to ensure that both sides of the back cover are reliably locked;
8. Pull out the back cover opening tool; pull out the pin protection cap while screwing it.
Product Description :
Fiber optic fast connector is used for field-installable optical fiber connector, widely used in Fiber To The Home (FTTH) access optical networks, not only for single-mode or multimode fiber, and can also choose to 900um,3 mm and the introduction of cable buffered type. With fast installation time and low insertion loss, the connector system provides a good alternative to fusion splicing.
Installation is as easy as strip, clean, cleave cam and crimp.
2.Low PDL
1.Fiber to the point (FTTX)
2.Fiber to the home (FTTH)
3.Passive optical networks(PON, GEPON)
4.Local area networks (LAN)
5.Cable television (CATV)
6.Test equipment
Installation is as easy as strip, clean, cleave cam and crimp.
Feature:
1. Low insertion loss2.Low PDL
3.Good channel-to-channel uniformity
4.Wide Operating Wavelength:From 1260nm to 1650nm
5.Wide Operating Temperature:From -40ºC to 85ºC
6.High Reliability and Stability
5.Wide Operating Temperature:From -40ºC to 85ºC
6.High Reliability and Stability
Applications :
1.Fiber to the point (FTTX)
2.Fiber to the home (FTTH)
3.Passive optical networks(PON, GEPON)
4.Local area networks (LAN)
5.Cable television (CATV)
6.Test equipment
Inspection:
| Item | Parameters | Item | Parameters |
| Mode | Single mode | Cladding Dia | 250 um |
| Cable Scope | 3.0x2.0 Bow type Cable | Fiber Dia | 125 um |
| Operating time | about 15s | Insertion loss | ≤0.25dB |
| Return loss | ≤-40dB | Continuous success rate | >98% |
| Assebly times | >10 times | Bare fiber tightening force | >5N |
| Tensile strength | >50N | Temperature range | -40~+85ºC |
| Online stretching resistance test(30N) | IL≤0.3dB | Mechanical endurance (500 times) | IL≤0.3dB |
| Fall-down test(on cement floor at height 4m/each direction one time/total three times | IL≤0.3dB | Application | FTTH/FTTX/FTTB |
Component list:
Back cover opening tool
Optical fiber connector back cover
Optical fiber connector body
Pin protection cap
Optical fiber connector protective jacket
Installation Notes :
For optical cable stripping, use sheathed cable stripping pliers to strip the sheathed cable with a length of about 60mm;
Use Miller pliers to peel off the 0.25mm coating, leaving about 24mm;
Wipe clean with absolute alcohol;
Use a fiber cleaver to cut the fiber, leaving a length of about 48mm;
Fiber positioning and fixing :
1. Screw the edge of the pin protection cap tightly and open the back cover of the optical fiber connector;
2. Use the back cover opening tool to buckle in and push forward according to the direction shown in the figure;
3. Insert the stripped optical cable into the guide hole in the middle;
4. When the outer sheath of the optical cable reaches the fixed teeth, tilt the optical cable by 30-45°;
5. Continue to push the optical cable until the core touches the ferrule protective cap;
6. Press the outer sheath of the optical cable into the tooth-shaped groove, and ensure that the optical fiber has a small amount of slight bending;
7. Close the back cover to ensure that both sides of the back cover are reliably locked;
8. Pull out the back cover opening tool; pull out the pin protection cap while screwing it.